Go Back   Exetools > General > General Discussion


Thread Tools Display Modes
Old 12-28-2004, 05:21
Posts: n/a
Question Some help needed

I want to modify the pe table section of executable, the thing is that I need to change the 'raw size' value by adding 200 to it. The original Raw size value is 000001E4 and i want to know how to figure out the new value after adding 200 to it. Im sorry I really dont know much about this sort of thing. thanks in advance!
Reply With Quote
Old 12-28-2004, 15:13
Posts: n/a
aligment of exe is 8 bit, so u can feel free to add 200h bytes to that segment
Reply With Quote
Old 12-29-2004, 06:38
Posts: n/a
and don't forget to change virtual size, if the fixed raw size is greater than virtual size. (unless they are padded with 0)
in such a case
if the section you want to modify is the last section you need to change the size of image too.
if it's the section in the middle, it's going to be little complex...
Reply With Quote
Old 12-29-2004, 06:53
Posts: n/a

hmmmm, karlss0n, thanks for the response but im still a bit confused....
I want to do this exactly;

000001E4 + 200 = 00000???
the "correct" answer is 000002C0, What I need to know how does this '000002C0' comes about. Where does that 'C" come from? lol, I'm sorry, I know this is probally a big stupid question and all.

Reply With Quote
Old 12-29-2004, 09:04
JMI JMI is offline
Join Date: Jan 2002
Posts: 1,627
Rept. Given: 5
Rept. Rcvd 199 Times in 99 Posts
Thanks Given: 0
Thanks Rcvd at 96 Times in 94 Posts
JMI Reputation: 100-199 JMI Reputation: 100-199
You need to read up on counting in hexadecimal.
It refers to the base-16 number system, which consists of 16 unique symbols: the numbers 0 to 9 and the letters A to F. The numbers are:

0, 1, 2, 3, 4, 5, 6, 7, 8, 9, A, B, C, D, E, F

For example, the decimal number 15 is represented as F in the hexadecimal numbering system. The hexadecimal system is useful because it can represent every byte (8 bits) as two consecutive hexadecimal digits. It is easier for humans to read hexadecimal numbers than binary numbers.
To convert a value from hexadecimal to binary, you merely translate each hexadecimal digit into its 4-bit binary equivalent. Hexadecimal numbers have either an 0x prefix or an h suffix. For example, the hexadecimal number


translates to the following binary number:

0011 1111 0111 1010

The base 16 notational system for representing real numbers. The digits used to represent numbers using hexadecimal notation are 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, A, B, C, D, E, and F. The following table gives the hexadecimal equivalents of the first few decimal numbers.

1 = 1 11 = B 21 = 15
2 = 2 12 = C 22 = 16
3 = 3 13 = D 23 = 17
4 = 4 14 = E 24 = 18
5 = 5 15 = F 25 = 19
6 = 6 16 = 10 26 = 1A
7 = 7 17 = 11 27 = 1B
8 = 8 18 = 12 28 = 1C
9 = 9 19 = 13 29 = 1D
10 =A 20 = 14 30 = 1E

and so on and so on.......

The hexadecimal system is particularly important in computer programming, since four bits (each consisting of a one or zero) can be succinctly expressed using a single hexadecimal digit. Two hexadecimal digits represent numbers from 0 to 255, a common range used, for example, to specify colors. Thus, in the HTML language of the web, colors are specified using three pairs of hexadecimal digits RRGGBB, where RR is the amount of red, GG the amount of green, and BB the amount of blue.

In hexadecimal, numbers with increasing digits are called metadromes, those with nondecreasing digits are called plaindrones, those with nonincreasing digits are called nialpdromes, and those with decreasing digits are called katadromes.

There's a good start.

Reply With Quote
Old 12-29-2004, 11:22
Posts: n/a
I don't see any way to land at 2C0h as the correct answer for any form of 1E4+200...

1E4h + 200h = 3E4h.
1E4h + 200d = 2ACh.
1E4h + 200o = 264h.

Where did you get 2C0h from?
Reply With Quote
Old 12-29-2004, 15:38
Posts: n/a

Thank you guys for all the input, you guys rule!

arkanoid, yes, Im padding it with 0s. Thanks.

Satyric0n, someone who knows a bit more than me told me 2C0h was correct and I took hes word for it, sorry about that. =)

JMI, that is exactly what I was searching for!... I just didnt know what topic to search under. Thank You!
I have a lot of reading up to do...thank you everyone!!!!!!!!!
Reply With Quote

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is Off
HTML code is Off

All times are GMT +8. The time now is 10:45.

Always Your Best Friend: Aaron, JMI, ahmadmansoor, ZeNiX, chessgod101
( 1998 - 2022 )